ALPS Manufacturer of Electronic Components/Parts Catalog
close
Top Page  > Products> TACT Switch(TM) > Surface Mount Type TACT Switch(TM)
 > SKSG Series > SKSGAAE010
Related information
｜Dimensions ｜Land Dimensions ｜Circuit Diagram ｜Packing Specifications ｜Soldering Conditions ｜

3.0×2.7mm Compact High Operating Force Type (Surface Mount) SKSG Series

Detail

Vertical type

Part number SKSGAAE010

Type Surface mount
Operating force 4N
Operating direction Vertical
Travel 0.12mm
Operating life
(5mA 5V DC) 		200,000 cycles
Initial contact resistance 100mΩ max.
Stem color Black
Minimum order unit (pcs.) 12,000

Series type Sharp feeling type
Operating temperature range -30℃ to +85℃
Rating (max.) 50mA 12V DC
Rating (min.) 10µA 1V DC
Electrical performance Insulation resistance 100MΩ min. 100V DC
Voltage proof 100V AC for 1 minute
Durability Vibration 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2 hours respectively
Environmental performance Cold -30±2℃ for 96h
Dry heat 80±2℃ for 96h
Damp heat 60±2℃, 90 to 95%RH for 96h

3D CAD (STEP)  
Certificate of Compliance to RoHS regulations  

Dimensions

Surface Mount Type TACT Switch(TM)

 
Ground terminal land pattern is applicable to Ground terminal type only.

Land Dimensions

Surface Mount Type TACT Switch(TM)

Circuit Diagram

Surface Mount Type TACT Switch(TM)


Packing Specifications

Taping

Number of packages (pcs.) 1 reel 12,000
1 case / Japan 120,000
1 case / export packing 120,000
Tape width (mm) 12
Export package measurements (mm) 401×401×214

Soldering Conditions

Condition for Reflow
1. Heating method
Double heating method with infrared heater.
2. Temperature measurement
Thermocouple 0.1 to 0.2 Φ CA(K) or CC(T) at solder joints (copper foil surface). A heat resisting tape should be used for fix measurement.
3. Temperature profile
(1) The above temperature shall be measured of the top of switch. There are cases where PC board's temperature greatly differs from that of the switch, depending on the material, size, thickness of PC board's and others. Care, should be taken to prevent the switch's surface temperature from exceeding 260℃.
(2) Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended.
Manual Soldering
ItemsCondition
Soldering temperature350℃ max.
Duration of soldering3s max.
Capacity of soldering iron60W max.
1. Consult with us for availability of TACT switch™ washing.
2. Prevent flux penetration from the top side of the TACT switchTM.
3. Switch terminals and a PC board should not be coated with flux prior to soldering.
4. The second soldering should be done after the switch returns to normal temperature.

Notes are common to this series/models.
  • This site catalog shows only outline specifications. When using the products, please obtain formal specifications for supply.
  • Please place purchase orders for taping products per minimum order unit (1 reel or a case).
  • For φ330mm diameter reel requirements, please contact us.
  • Please contact us for automotive use.
Inquiries about Products
For more information please contact: Products Information Center.
1-7, Yukigaya-otsukamachi, Ota-ku, Tokyo, 145-8501, Japan
Phone: +81 (3) 5499-8154
COPYRIGHT(C) 1995-2012 ALPS ELECTRIC CO., LTD.