ALPS Manufacturer of Electronic Components/Parts Catalog
close
Top Page  > Products> TACT Switch(TM) > Snap-in Type TACT Switch(TM)
 > SKHL Series > SKHLAKA010
Related information
｜Photo Stem color : Red ｜Dimensions ｜Mounting Hole Dimensions ｜Circuit Diagram ｜
｜Packing Specifications ｜Soldering Conditions ｜

6.0×3.5mm Compact Type (Snap-in) SKHL Series

Detail

Vertical type

Part number SKHLAKA010

Type Snap-in
Operating force 2.55N
Operating direction Vertical
Travel 0.25mm
Operating life
(5mA 12V DC) 		30,000 cycles
Initial contact resistance 500mΩ max.
Stem color Red
Stem height h=5mm
Minimum order unit (pcs.) 1,000

Series type Sharp feeling type
Operating temperature range -20℃ to +70℃
Rating (max.) 50mA 12V DC
Rating (min.) 10µA 1V DC
Electrical performance Insulation resistance 100MΩ min. 100V DC
Voltage proof 250V AC for 1 minute
Durability Vibration 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2 hours respectively
Environmental performance Cold -30±2℃ for 96h
Dry heat 80±2℃ for 96h
Damp heat 60±2℃, 90 to 95%RH for 96h

Certificate of Compliance to RoHS regulations  

Photo Stem color : Red

Snap-in Type TACT Switch(TM)

Dimensions

Snap-in Type TACT Switch(TM)

Mounting Hole Dimensions

Snap-in Type TACT Switch(TM)

 
Viewed from mounting face.

Circuit Diagram

Snap-in Type TACT Switch(TM)


Packing Specifications

Bulk
Number of packages (pcs.) 1 case / Japan 10,000
1 case / export packing 30,000
Export package measurements (mm) 309×476×347

Soldering Conditions

Conditions for Auto-dip
ItemsCondition
Flux built-upMounting surface should not be exposed to fluk
Preheating temperatureAmbient temperature of the soldered surface of PC board.
100℃ max.
Preheating time60s ax.
Soldering temperature260℃ max.
Duration of immersion5s max.
Number of soldering2times max.
Manual Soldering
ItemsCondition
Soldering temperature350℃ max.
Duration of soldering3s max.
Capacity of soldering iron60W max.
1. Consult with us for availability of TACT switch™ washing.
2. Prevent flux penetration from the top side of the TACT switchTM.
3. Switch terminals and a PC board should not be coated with flux prior to soldering.
4. The second soldering should be done after the switch returns to normal temperature.
5. Use the flux with a specific gravity of at least 0.81.
(MH-820V or CF220V by TAMURA Corporation, or their equivalents.)

Notes are common to this series/models.
  • This site catalog shows only outline specifications. When using the products, please obtain formal specifications for supply.
  • Please use 1.6mm thick PC boards.
  • Please place purchase orders per minimum order unit (integer).
  • This products can be used in vehicles.
    Although these products are designed to perform over a wide operating temperature range, please ensure that you receive and read the formal delivery specifications before use.
Inquiries about Products
For more information please contact: Products Information Center.
1-7, Yukigaya-otsukamachi, Ota-ku, Tokyo, 145-8501, Japan
Phone: +81 (3) 5499-8154
COPYRIGHT(C) 1995-2012 ALPS ELECTRIC CO., LTD.